Promastic – premium pre-mixed quick grabbing, non-slip,mastic adhesive-Technical Data Sheet.

Description

Promastic is a premium pre-mixed mastic adhesive. It is a quick grabbing, non-slip, flexible wall tile adhesive, which allows tiling to begin from any position on the wall. Promastic exceeds the requirements of Australian Standards AS 2358-1990.
Precautions

Promastic is unsuitable for:

*
bonding to moisture sensitive green marble;
*
bonding to painted walls;
*
bonding to substrates subject to constant water immersion such as swimming pools.

Surface Preparation

All surfaces to be tiled must be flat and true, free from oil, dirt, grease or any other contaminants. Very porous surfaces should be primed with Plastinex (1 part Plastinex mixed with 4 parts water).

Concrete : New concrete must be allowed to cure for 6 weeks and should have a wood flat finish. When finished with a steel trowel, concrete must be acid etched, using Floor Prep.

Cement Render : Render to be left with a wood float finish and allowed to cure for 7 days.

Fibre Cement Sheets : Compressed fibre sheets should be primed with Plastinex (1 part Plastinex mixed with 4 parts water) and all joints to be taped with PVC duct tape and fixed according to manufacturer’s instructions.

Plasterboard : Must be fixed as per manufacturer’s instructions. Jointing compound must be primed with Plastinex (1 part Plastinex mixed with 4 parts water).

Mixing Promastic

Promastic is pre-mixed and ready for use straight from the container.

Open Time

Promastic has an open time of approximately 1 hour, which can be shortened to just a few minutes by the action of sun, wind, high temperatures or highly absorbent surfaces. Tilers need to constantly check that the adhesive has not formed a surface skin and is still fresh to the touch.

Wetting or priming the substrate prior to tiling prolongs the open time of the adhesive. It is not advisable to wet the adhesive when it has formed a skin as water only increases the rate of cement hydration and will result in an anti adhesive film. Skinned adhesive must always be removed and disposed of.

Application

Always install the tiles in accordance with AS 3958 1:1991 and ensure the backs of the tiles are free of dust. Spread Promastic evenly across one square metre at a time with a 6 x 6 x 6 notched trowel for walls or a 10 x 10 x 10 notched trowel for floors. The choice of trowel should be governed by the depth of the knobs, grooves or ridges on the back of the tile and the evenness of the substrate.

Lay the tiles with a fair pressure and at right angles to the notched pattern.

The final bed of adhesive should be between 2mm and 4mm. Wall tiles should have a finished joint width of 2mm – 4mm and floor files a finished joint width of 3mm – 6mm. Tiles can be adjusted for approximately 40 minutes after laying.

Coverage

22kgs of Promastic will cover approximately 10-12 square metres with a 6mm notched trowel for walls.

Dry Time

Promastic dries in approximately 24 hours at 23oC and 50% relative humidity. It may require longer times to cure for denser tiles and substrates or at installation temperatures below 10oC.

Expansion Joints

Joint Grouting

Grouting may commence after approximately 24 hours (depending on variables such as sun, heat, wind, etc.)

Shelf Life

Promastic can be stored in the original packaging in a dry elevated position for 12 months.

Packaging

Promastic is available in 20kg buckets.

Guarantee

Product Datasheet

Morgan Ceramic Tile Adhesives

http://www.morganadhesives.com.au
11 Raymond Avenue
Bayswater 6053
Western Australia

Telephone +61 8 9272 4666
Facsimile +61 8 9370 1744

Email: info@morganadhesives.com.au

Account queries email accounts@morganadhesives.com.au